AsyncLabs Forums

[tkj]

And here it is...

Working:

• 2Wire Residential Gateway 3800HGV-B
• Airlink101 AR430W with DD-WRT ver 24sp1
• Apple Airport Extreme base station 7.4.1
• Belkin F5D7230-4
• Belkin F5D7234-4 (only when no encryption is used)
• Bell Sympatico (2Wire 2701HG-G) (using WEP)
• Buffalo AirStation Wireless-G High Power (w/ DD-WRT firmware)
• CradlePoint MBR1000 3G/WiFi router
• DIR-655 (with a little workaround)
• DLink-615 with C1 Firmware Version: 3.10NA
• D-Link 624+ with Firmware 1.18
• D-Link DIR-655 (only when no encryption is used)
• D-Link DWL200AP Fw. 1.7
• D-Link WBR-2310 (Revision: A1, Firmware Version: 1.05)
• Draytek Vigor 2820
• Juniper SSG5-Serial-WLAN (6.0.0r5a.0 - Firewall+VPN)
• Linksys WRT120N fully working with WPA2 and WEP
• Linksys WRT310N V1.0.07-LS-HND
• Linksys WRT350N V2.00.17
• Linksys WRT54G v2 (firmware version 4.21.1), unsecure and WEP 64bit
• Linksys WRT54G v2 and v2.2 with WRT54GL firmware v4.30.14
• Linksys WRT54GL Tomato
• Linksys WRT54GL DD-WRT
• Linksys WRT54GS DD-WRT
• Linksys WRT54GS v6 w/ OEM Firmware (works with WPA AES, but not WPA TKIP)
• Linksys WRT54G2 V1.0.03
• Linksys WRT610n
• Motorola 3347
• Netgear DG834G V3
• NetGear WG602v4
• Netgear WGT624 V3
• Netgear WNR2000
• Siemens Gigaset SE505 (firmware version nl_3.01.05)
• Sitecom WL-153 Rev. A
• Verizon MiFi 2200 (WEP/WPA ok, WPA2 not working)

Not working:

• 2Wire Router/DSL modem combination
• Actiontec GT704-WG
• D-Link 524
• D-Link 624
• D-Link DWL2000AP
• Linksys WAP11
• Linksys WRT54G ver 1.1 (factory firmware)
• Microsoft MN-700
• Netgear WNDR3700 v1.0.4.68NA
• TOPCOM Skyracer WBR 244
• Zyxel G1000v2

It would be nice with a Compatible Accesspoint List of working and non-working Accesspoints!

Best Regards
Thomas Jespersen

[MOS6502]

I don't know where this is gonna end up - but I figure ill start. Ive personally had a chance to mess around with 2 routers...

Works
- Linksys WRT54GL using custom firmware Tomato and DD-WRT

Doesn't work
- 2wire 2701HG-B Gateway

Edited to specify 2wire router model number**

[gsxrex]

Ok, I'll compile all the access points if people post to this thread. I'll also cross-reference this back to the wiki with all the other documentation. Please list your make and model, as well as the firmware version that you are running.

Just keep in mind that to take this information with a grain of salt. There are many factors that can influence wireless operation.

Working:
Linksys WRT54GL Tomato
Linksys WRT54GL DD-WRT
Linksys WRT54GS DD-WRT
Linksys WRT54G2 ver 1.0.03
2Wire Residential Gateway 3800HGV-B
Apple Airport Extreme base station 7.4.1

Not working:
2Wire Router/DSL modem combination
TOPCOM Skyracer WBR 244
Zyxel G1000v2

[tkj]

I can say that I can't get the WiShield connected to a TOPCOM Skyracer WBR 244.
So that's a non-working

[pisarm]

Not working on a Zyxel G1000v2 access point.

[zhobbs]

Works here with a Belkin F5D7230-4

[rusty]

So far, what's worked for me:
Airlink101 AR430W w/ DD-WRT v24sp1 -- Fry's sold this puppy for $10 around Thanksgiving (US) 2008.
I have WEP and WPA-PSK working. Haven't tried Open or WPA2 yet.

What hasn't worked for me:
Linksys WRT54g v1.1 w/ factory firmware

Arduino's using software current as of May 20th, 2009.
For the last day or so my WiShield has stayed connected to my Airlink101
for well over 24-hours. I'm starting to become impressed!

[gordonendersby]

Working this evening using WPA2 on a Netgear WGT624 V3.

Thanks

Gordon

[Pablo]

Hello

Working on Netgear DG834G V3

[GregEigsti]

Working on a Buffalo AirStation Wireless-G High Power which runs DD-WRT firmware. Of course 802.11b is enabled